View NS5B1G384_4675976.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NS5B1G384 Single (NC) Normally Closed SPST Analog Switch
The NS5B1G384 is Single Pole Single Throw (SPST) high-speed TTL-compatible switch. The low resistance and capacitance characteristics of this switch make it ideal for low-distortion audio, video, and data routing applications. The switch has a normally closed logic configuration meaning the switch is on (NC connected to COM) when IN is low. These switches are available in 5-pin SC-70 and 5-pin TSOP-5 (SOT23-5) packages for operation over the industrial (-40C to +85C) temperature range.
Features http://onsemi.com MARKING DIAGRAMS
SC-70 CASE 419A AG MG G
* * * * * * * * * * *
VCC Operating Range: 2.0 V to 5.5 V Low On Resistance : RON: 4.0 W Typical @ VCC = 4.5 V Minimal Propagation Delay : tpd < 0.5 ns Control Input Compatible with TTL Levels ESD Performance: Human Body Model > 2 kV 5-Pin SC-70 or 5-Pin TSOP-5 Packages Available These are Pb-Free Devices Audio, Video, and High-Speed Data Switching Mobile Phones Portable Devices Desktop & Notebook Computing
5 5 1 AG AD M G TSOP-5 (SOT23-5) CASE 483 AD MG G 1
Typical Applications
= For SC-70 = For TSOP-5 = Date Code = Pb-Free Package
(Note: Microdot may be in either location)
LOGIC DIAGRAM
NC IN COM
PIN ASSIGNMENTS
COM
1
5
VCC
NC
2
GND
3
4
IN
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2009
March, 2009 - Rev. 0
1
Publication Order Number: NS5B1G384/D
NS5B1G384
PIN DESCRIPTION
PIN # 1 2 3 4 5 Name COM NC GND IN VCC Direction I/O I/O Input Input Input Description Common Signal Line Normally Closed Signal Line Ground Control Signal Line Voltage Supply
TRUTH TABLE
IN Control Input L H Function NC Connected to COM NC Disconnected from COM
MAXIMUM RATINGS
Symbol VCC VIS VIN IIS_CON IIS_PK IIN TSTG Pins VCC NC or COM IN NC or COM NC or COM IN Rating Positive DC Supply Voltage Analog Signal Voltage Control Input Voltage Analog Signal Continuous Current Analog Signal Peak Current Control Input Current Storage Temperature Range Value -0.5 to +7.0 -0.5 to VCC + 0.5 -0.5 to +7.0 $300 $500 $20 -65 to 150 Closed Switch 10% Duty Cycle Condition Unit V V V mA mA mA C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VIS VIN TA tr, tf Pins VCC NC or COM IN Parameter Positive DC Supply Voltage Analog Signal Voltage Control Input Voltage Operating Temperature Range Input Rise or Fall Time Value 2.0 to 5.5 GND to VCC GND to 5.5 -40 to +85 20 10 VCC = 3.3 V VCC = 5.0 V Condition Unit V V V C ns/V
Minimum and maximum values are guaranteed through test or design across the Recommended Operating Conditions, where applicable. Typical values are listed for guidance only and are based on the particular conditions listed for each section, where applicable. These conditions are valid for all values found in the characteristics tables unless otherwise specified in the test conditions.
ESD PROTECTION
Pins All Pins Description Human Body Model Minimum Voltage 2 kV
http://onsemi.com
2
NS5B1G384
DC ELECTRICAL CHARACTERISTICS
CONTROL INPUT (Typical: T = 25C)
Symbol VIH VIL IIN Pins IN IN IN Parameter Control Input High Control Input Low Control Input Leakage 0 v VIN v VCC Test Conditions VCC (V) 4.5 - 5.5 4.5 - 5.5 5.0 0.1 -405C to +855C Min 2.0 0.8 0.5 Typ Max Unit V V mA
SUPPLY CURRENT AND LEAKAGE (Typical: T = 25C)
Symbol INC (OFF) ICOM (OFF) ICC IOFF Pins NC Parameter OFF State Leakage Test Conditions VIN = VIL or VIH VNC = 1.0 V VCOM = 4.5 V VIN = VIL or VIH VNC = 4.5 V VCOM = 1.0 V VIN and VIS = VCC or GND ID = 0 A VIN = 5.5 V or GND VCC (V) 5.5 -405C to +855C Min Typ 10 Max 100 Unit nA
COM
OFF State Leakage
5.5
10
100
nA
VCC IN
Quiescent Supply Power Off Leakage
2.0 - 5.5 0
0.1 0.5
1.0 1.0
mA mA
ON RESISTANCE (Typical: T = 25C)
Symbol RON Pins NC, COM Parameter ON Resistance Test Conditions VIS = 0 V, ION = 30 mA VIS = 0 V, ION = 64 mA VIS = 2.4 V, ION = 15 mA VCC (V) 4.5 4.5 4.5 -405C to +855C Min Typ 4.0 4.0 11.5 Max 7.0 7.0 15 Unit W
http://onsemi.com
3
NS5B1G384
AC ELECTRICAL CHARACTERISTICS
TIMING/FREQUENCY (Typical: T = 25C, RL = 50 W, CL = 35 pF, f = 1 MHz)
Symbol tON tOFF tPD BW Pins IN to NC IN to NC NC to COM Parameter Turn On Time Turn Off Time Propagation Delay -3dB Bandwidth CL = 5 pF, Figures 3 and 4 Test Conditions As Above, Figures 1 and 2 As Above, Figures 1 and 2 VCC (V) 4.5 4.5 4.5 4.5 330 -405C to +855C Min Typ Max 6.0 2.0 0.5 Unit ns ns ns MHz
CAPACITANCE (Typical: T = 25C, RL = 50 W, CL = 5 pF, f = 1 MHz)
Symbol CIN CON COFF Pins IN NC to COM NC Parameter Control Input Through Switch Unselected Port VIN = 0V VIS = 4.5 V, VIN = 4.5 V Test Conditions VCC (V) 0V 4.5 V 4.5 V -405C to +855C Min Typ 2.2 12 4.1 Max Unit pF pF pF
DEVICE ORDERING INFORMATION
Device Order Number NS5B1G384DFT2G NS5B1G385DTT1G Package Type SC-70 (Pb-Free) TSOP-5 (Pb-Free) Tape & Reel Size 3000 / Tape & Reel 3000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
4
NS5B1G384
VCC DUT VCC 0.1 mF Open Output VOUT 50 W 35 pF Output VOL Input tON tOFF Input 0V VOH 50% 50%
90%
90%
Figure 1. tON/tOFF
VCC DUT Output Open 50 W VOUT 35 pF Input
VCC 50% 0V VOH Output VOL 10% tOFF tON 10% 50%
Input
Figure 2. tON/tOFF
50 W Reference Input Output 50 W Generator 50 W DUT Transmitted
Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction. VISO = Off Channel Isolation = 20 Log VONL = On Channel Loss = 20 Log VOUT VIN for VIN at 100 kHz
VOUT for VIN at 100 kHz to 50 MHz VIN
Bandwidth (BW) = the frequency 3 dB below VONL VCT = Use VISO setup and test to all other switch analog input/outputs terminated with 50 W
Figure 3. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/VONL
http://onsemi.com
5
NS5B1G384
0 -1 MAGNITUDE (dB) MAGNITUDE (dB) -2 -3 -4 -5 -6 10000 -10 -20 -30 -40 -50 -60 -70 -80 -90 1000000 FREQUENCY (Hz) 100000000 -100 10000 1000000 FREQUENCY (Hz) 100000000
Figure 4. Typical Bandwidth @ VCC = 5.5 V, 255C
Figure 5. Off-Channel Isolation @ VCC = 5.5 V, 255C
0.06 0.05
PERCENT (%)
0.04 0.03 0.02 0.01 0 10
100
1000
FREQUENCY (Hz)
10000
100000
Figure 6. Typical Total Harmonic Distortion @ VCC = 4.5 V
http://onsemi.com
6
NS5B1G384
PACKAGE DIMENSIONS
SC-70, SOT-353, SC-88A CASE 419A-02 ISSUE J
A G
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20
5
4
S
1 2 3
-B-
D 5 PL
0.2 (0.008)
M
B
M
N J C
DIM A B C D G H J K N S
H
K
http://onsemi.com
7
NS5B1G384
PACKAGE DIMENSIONS
TSOP-5, SOT23-5 CASE 483-02 ISSUE H
NOTE 5 2X
D
5X
0.10 T 0.20 T L A
5 1 2 4 3
0.20 C A B M
2X
B
S K
DETAIL Z
G
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. DIM A B C D G H J K L M S MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00
DETAIL Z
C 0.05 H T
SEATING PLANE
J
SOLDERING FOOTPRINT*
0.95 0.037 1.9 0.074
2.4 0.094 1.0 0.039 0.7 0.028
mm inches
SCALE 10:1
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
8
NS5B1G384/D

▲Up To Search▲

Price & Availability of NS5B1G384

	To Download NS5B1G384 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .